Engine not running smoothly / (hesistant)

Make: Alfa Romeo
Model: 159 Factory Service Manual
Year: 2005–2011
Section: Engine › Engine not running smoothly / (hesistant)

‹ Prev Gear engagement sensitivity poor Next › Engine not running smoothly / (losing power)

Fault diagnosisEngine not running smoothly / (hesistant)

ENGINE NOT RUNNING SMOOTHLY / (HESISTANT)

1.9 JTS, 2.2 JTS, 3.2 JTS

There are momentary failures in the response to pressing the accelerator pedal. This condition may take place at any vehicle speed. This condition is usually more pronounced when setting off again after a stop and can also cause the engine to stall if it is serious enough.

0	PRELIMINARY CHECKS	All OK	Problems encountered	Operation
		Test results
	Before starting, check that the MIL warning light is on and that it goes off once the engine has been started. Also check that no accessories have been fitted in the after-market	Move on to Step 1	The MIL warning lights does not come on when the key is inserted	Continue as instructed in the See table K100 MIL WARNING LIGHT NOT WORKING (REMAINS OFF BEFORE STARTING)
			The MIL warning light remains on with the engine started	Continue as instructed in the See table K101 MIL WARNING LIGHT STAYS ON (ENGINE STARTS)
			There are accessories that have been fitted in the after-market	Check that these accessories have been fitted correctly
1	CONTROL UNIT ELECTRICAL CONNECTIONS CHECK	All OK	Problems encountered	Operation
	Check that the electrical connections for the engine management control unit are correct See E5030 PETROL ENGINES ELECTRONIC MANAGEMENT In particular, check that: - the earth is correctly connected - the resistance between the control unit See M010 ENGINE MANAGEMENT ECU and the battery negative See A001 BATTERY is less than 0.5 Ohm	Move on to Step 2	Connection to earth incorrect	Restore the correct connections
		Move on to Step 2	Resistance to battery negative more than 0.5 Ohm	Restore the correct connections
2	CONTROL UNIT FASTENING CHECK	All OK	Problems encountered	Operation
	Check that the control unit is correctly fastened in its housing Op. 1056F82 CONTROL UNIT SINGLE OF INJECTION IGNITION SYSTEM R R	Move on to Step 3	Control unit fastening incorrect	Renew the correct fastening for the control unit Op. 1056F82 CONTROL UNIT SINGLE OF INJECTION IGNITION SYSTEM R R
3	AIR INTAKE CIRCUIT CHECK	All OK	Problems encountered	Operation
	Check there are no faults in the air intake circuit. In particular, check: - that the air filter is not blocked or fitted incorrectly - that the air intake circuit does not have any irregular constrictions, leaks or is fitted incorrectly	Move on to Step 4	Air filter blocked	Replace the filter element Op. 1048A14 AIR CLEANER FILTER ELEMENT - REPLACE.
			Irregular component	Replace the faulty component Op. 1048 ENGINE AIR SUPPLY CIRCUIT
			Component incorrectly positioned	Refit the component correctly Op. 1048 ENGINE AIR SUPPLY CIRCUIT
4	LAMBDA SENSOR CHECK	All OK	Problems encountered	Operation
	Check that the Lambda sensor upstream of the catalyzer is working properly, by carrying out the See Test 1080BA UPSTREAM LAMBDA SENSOR OPERATION CHECK	Move on to Step 5	Faults present	The operation to solve the problem is described in the actual test
5	FLOW METER ERRORS CHECK	All OK	Problems encountered	Operation
	Connect the diagnostic equipment and check that error P0100 is not present	Move on to Step 6	Error P0100 is present	Continue as described by the diagnostic equipment
6	FUEL FEED CIRCUIT CHECK	All OK	Problems encountered	Operation
	Check there are no faults in the fuel supply circuit by performing the See Test 1040OA FUEL SUPPLY CIRCUIT CHECK	Move on to Step 7	Faults present	The operation to solve the problem is described in the actual test
7	CHECK FOR THE PRESENCE OF IMPURITIES IN THE FUEL	All OK	Problems encountered	Operation
	Check that there are no impurities such as water, alcohol or particles in suspension in the fuel by carrying out the test See T FUEL QUALITY CHECK	Move on to Step 8	Faults present	The operation to solve the problem is described in the actual test
8	INJECTOR CHECK	All OK	Problems encountered	Operation
	Check that the injectors are not stuck shut or not perfectly closed by carrying out the See Test 1056BA INJECTOR OPERATION CHECK	Move on to Step 9	Faults present	The operation to solve the problem is described in the actual test
9	IGNITION COIL CHECK	All OK	Problems encountered	Operation
	Check that the ignition coils are correctly fitted in their seats. Also check that they do not show signs of corrosion or dampness. Lastly, check that the ignition coils are working properly, by carrying out the See Test 5510CC IGNITION COIL CHECK	Move on to Step 10	One of the coils is not fitted correctly	Refit the coil correctly Op. 5510C14 IGNITION COIL/S - R.R.
			One of the coils shows signs of corrosion/dampness	Replace the coil Op. 5510C14 IGNITION COIL/S - R.R.
			One of the coils is not working properly	The operation to solve the problem is described in the actual test
10	SPARK PLUGS CHECK	All OK	Problems encountered	Operation
	Remove the spark plugs Op. 5510D10 SPARK PLUGS - R+R and check that they are no signs of faults, following the instructions in the test See T SPARK PLUG STATE CHECK	Move on to Step 11	Faults present	The operation to solve the problem is described in the actual test
11	RPM SENSOR CHECK	All OK	Problems encountered	Operation
	Check that the resistance value of the rpm sensor in all temperature ranges is between 700 and 1200 Ohm	Move on to Step 12	Resistance values outside of the range	Change the rpm sensor Op. 5510C26 ENGINE RPM SENSOR - R+R
12	PHASE TRANSFORMER ERRORS CHECK	All OK	Problems encountered	Operation
	Connect the diagnostic equipment and check that none of the following errors is present: P0011, P0014	Move on to Step 13	One or more of the errors indicated is present	Continue as described by the diagnostic equipment
13	ALTERNATOR CHECK	All OK	Problems encountered	Operation
	Check that the alternator output voltage is between 9 and 16 V	Move on to Step 14	Output voltage below 9 V	Check that the alternator is working properly by carrying out the See Test 5530AB Check alternator operation
		Move on to Step 14	Output voltage above 16 V	Replace the pressure regulator Op. 5530A24 ALTERNATOR VOLTAGE REGULATOR - R.R. WITH ALTERNATOR REMOVED
14	CHECK ON CORRECT OPERATION	All OK	Problems encountered	Operation
	Check the fault has disappeared	End of diagnosis	The fault persists	Contact the Technical Expert for further information on the problem

‹ Prev Gear engagement sensitivity poor Next › Engine not running smoothly / (losing power)

Parts & tools for this job Staging For 2005 Alfa Romeo 159

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.