Workshop Manuals Factory service & repair Lancia
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Axles and driveshafts12 Brakes13 Steering14 Suspension and wheels15 Heating, air conditioning and auxiliary units16 Electrical equipment17 Body fittings18 Body panels and frame19 Wiring diagrams and electrical functions20 Wiring harnesses21 Connectors and pin-outs22 Fault diagnosis23 Service news bulletins24 Special tools
Lancia Thesis Factory Service Manual (2002-2009)08 · Engine
08 · Engine

CAMSHAFT in cylinder head - R.R. on vehicle

Make
Lancia
Model
Thesis Factory Service Manual
Year
2002–2009
Section
Timing system › CAMSHAFT in cylinder head - R.R. on vehicle
EngineCAMSHAFT in cylinder head - R.R. on vehicle

CAMSHAFT in cylinder head - R.R. on vehicle

Operation 1036B10 · CAMSHAFT (1) IN CYLINDER HEAD (1)

2.0 TB, 2.4 20V, 3.0 V6, 3.2 V6

- Procedure not yet available

2.4 JTD 10V

Removing

See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.

See in Op. 1016A10 SOUND-PROOFING COVER - R.R.

See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.

See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.

See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.

See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.

See in Op. 1092G10 Engine components single drive BELT - R.R.

See in Op. 1032D12 Timing system protective COVER(S) - R.R.

See in Op. 1032B10 TOOTHED timing BELT - R.R. for timing adjustment or replacement

See in Op. 1032B40 TOOTHED DRIVEN PULLEY (one) - R.R. with timing belt removed

See in Op. 3330D30 vacuum pump - r+r

See in Op. 1016A20 Single TAPPET COVER - R.R. and Replace gasket

1. Undo the fixing bolt (1a) and remove the camshaft bearings lubrication pipe (1b).

2. Undo the bolts (2a) and remove the camshaft caps (2b).

3. Remove the camshaft (3a) complete with oil seal (3b).

CAMSHAFT in cylinder head - R.R. on vehicle

Refitting

- Fit the camshaft in the cylinder head.

- Tighten the bolts fixing the caps.

- Position the lubrication pipe and fasten it tightening the fixing bolts.

- Tighten the bolts fixing the caps to torque.

Value - daNmFasteningComponentØ
1.5BoltCAMSHAFT CAPSM7

1. Introduce the new oil seal (1b) into the camshaft using the tool (1a).

DescriptionCodeFunction
1aFitting tool1.860.824.000Tool for fitting crankshaft front oil seals
CAMSHAFT in cylinder head - R.R. on vehicle

See in Op. 1016A20 Single TAPPET COVER - R.R. and Replace gasket

See in Op. 3330D30 vacuum pump - r+r

See in Op. 1032B40 TOOTHED DRIVEN PULLEY (one) - R.R. with timing belt removed

See in Op. 1032B10 TOOTHED timing BELT - R.R. for timing adjustment or replacement

See in Op. 1032D12 Timing system protective COVER(S) - R.R.

See in Op. 1092G10 Engine components single drive BELT - R.R.

See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.

See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.

See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.

See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.

See in Op. 1016A10 SOUND-PROOFING COVER - R.R.

See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.

Parts & tools for this job Staging For 2002 Lancia Thesis

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.