Workshop Manuals Factory service & repair Lancia
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Axles and driveshafts12 Brakes13 Steering14 Suspension and wheels15 Heating, air conditioning and auxiliary units16 Electrical equipment17 Body fittings18 Body panels and frame19 Wiring diagrams and electrical functions20 Wiring harnesses21 Connectors and pin-outs22 Fault diagnosis23 Service news bulletins24 Special tools
Lancia Thesis Factory Service Manual (2002-2009)08 · Engine
08 · Engine

Driven toothed pullies

Make
Lancia
Model
Thesis Factory Service Manual
Year
2002–2009
Section
Timing system › Driven toothed pullies
EngineDriven toothed pullies

DRIVEN TOOTHED PULLIES

Operation 1032B58 · BELT-DRIVEN TIMING SYSTEM

3.0 V6, 3.2 V6

Removing

- Position the vehicle on a lift.

- Open the boot, remove the cover on the left hand side and disconnect the negative battery lead.

See in Op. 4450B04 Right FRONT WHEEL (one) - R.R.

- Raise the vehicle on the lift.

See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.

See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.

See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.

See in Op. 1092G10 Engine components single drive BELT - R.R.

- Lower the lift.

See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.

See in Op. 1088B10 Engine coolant SUPPLY RESERVOIR - R.R.

See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.

See in Op. 1048A28 vacuum air circuit resonator pipe - r+r

See in Op. 1008C10 Power unit REACTION ROD - Replace

See in Op. 1016A42 LEFT CYLINDER HEAD IGNITION COIL COVER - R.R.

See in Op. 1048A11 COMPLETE AIR FILTER -R.R.

See in Op. 1032B10 TOOTHED timing BELT - R.R. for timing adjustment or replacement

1. Undo the bolts (1a) for the right head driven toothed pullies using the tool (1b) for counter-torque.

DescriptionCodeFunction
1bCounter-torque1.860.856.000Lock the rotation of the driven toothed pulley
DRIVEN TOOTHED PULLIES

1. Remove the right head driven toothed pullies (1a) using the tool (1b).

DescriptionCodeFunction
1bExtractor1.860.954.001Remove the driven toothed pulley
DRIVEN TOOTHED PULLIES

Refitting

- Fit the right head driven toothed pullies and secure them without tightening the bolts.

See in Op. 1032B10 TOOTHED timing BELT - R.R. for timing adjustment or replacement

See in Op. 1048A11 COMPLETE AIR FILTER -R.R.

See in Op. 1016A42 LEFT CYLINDER HEAD IGNITION COIL COVER - R.R.

See in Op. 1008C10 Power unit REACTION ROD - Replace

See in Op. 1048A28 vacuum air circuit resonator pipe - r+r

See in Op. 1048A21 AIR INLET HOSE FROM INTAKE TO FILTER - R.R.

See in Op. 1088B10 Engine coolant SUPPLY RESERVOIR - R.R.

See in Op. 7040D50 ENGINE COMPARTMENT UPPER SOUND INSULATION SHIELD - R.R.

- Raise the lift.

See in Op. 1092G10 Engine components single drive BELT - R.R.

See in Op. 7055B42 FRONT WHEEL ARCH LINER (one), left or right - R.R.

See in Op. 7055B64 Engine compartment DUST SEAL in front wheel arch (one), left or right - R.R.

See in Op. 7055B54 PROTECTION/GUARD under engine - R.R.

- Lower the vehicle.

- Connect the negative battery lead, then close the boot.

See in Op. 0010T20 Engine REFRIGERANT FLUID - Change

- Remove the vehicle from the lift.

Parts & tools for this job Staging For 2002 Lancia Thesis

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.