Engine oil pump - r+r
- Make
- Alfa Romeo
- Model
- GT Factory Service Manual
- Year
- 2003–2010
- Section
- Engine lubrication system › Engine oil pump - r+r
ENGINE OIL PUMP - R+R
Removing
Position the vehicle on a lift.
Make sure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-)
| Description | Connector | |
|---|---|---|
| Battery | See A1B BATTERY ( BATTERY NEGATIVE ) |
Proceed with the removal
Op. 4450B04 RIGHT FRONT WHEEL R R.
Proceed with the removal
Op. 7055B64 LH OR RH REFLECTOR(ONE) ON REAR BUMPERS - R R.
Proceed with the removal
Op. 1092G10 SINGLE ENGINE BELT R R.
Proceed with the removal
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Proceed with the removal
Op. 1076B82 LEFT EXHASUST PIPE BETWEEN CATALYTIC PRECONVERTER AND CONVERTER R R.
Proceed with the removal
Op. 5510C34 RPM AND TIMING SENSOR (SINGLE) - R+R.
Proceed with the removal
Op. 1020A20 CRANK CASE OIL SUMP - R + R CLEAN SEALS FOR SEALANT APPLICATION.
1. Fit the crankshaft pulley counter-torque tool.
| Description | Code | |
|---|---|---|
| 1 | Counter-torque for crankshaft | 1.870.646.000 |
1. Undo the bolt fixing the drive chain to the engine oil pump.
1. Release the drive chain (1a) from the engine oil pump using the tool (1b).
| Description | Code | |
|---|---|---|
| 1b | Extractor | 1.860.954.001 |
2. Undo the bolts (2a) and remove the engine oil pump (2b).
Refitting
1. Position the engine oil pump (1a) in its housing and secure it tightening the bolt (1b) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1b | Bolt | ENGINE OIL PUMP | M10 | (Main bearing caps side) 4.5 - 5.5 |
2. Place the drive chain (2a) on the engine oil pump and secure it tightening the bolt (2b) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 2b | Bolt | ENGINE OIL PUMP DRIVE CHAIN | M10 | (Engine oil pump side) 4.5 - 5.5 |
Remove the crankshaft pulley counter-torque tool.
| Description | Code | |
|---|---|---|
| Counter-torque for crankshaft | 1.870.646.000 |
Proceed with the refitting
Op. 1020A20 CRANK CASE OIL SUMP - R + R CLEAN SEALS FOR SEALANT APPLICATION.
Proceed with the refitting
Op. 5510C34 RPM AND TIMING SENSOR (SINGLE) - R+R.
Proceed with the refitting
Op. 1076B82 LEFT EXHASUST PIPE BETWEEN CATALYTIC PRECONVERTER AND CONVERTER R R.
Proceed with the refitting
Op. 1092G10 SINGLE ENGINE BELT R R.
Proceed with the refitting
Op. 7055B64 LH OR RH REFLECTOR(ONE) ON REAR BUMPERS - R R.
Proceed with the refitting
Op. 4450B04 RIGHT FRONT WHEEL R R.
Refill the engine oil lubrication system
Op. 0010T11 ENGINE OIL CHECK LEVEL AND TOP UP.
Proceed with the refitting
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Connect the negative battery terminal (-).
Remove the vehicle from the lift.
Parts & tools for this job Staging For 2003 Alfa Romeo GT
- PARTEngine gasket setSearch: Alfa Romeo GT 2003 engine gasket set
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLFeeler gauge setSearch: feeler gauge set
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.