22 · Diagnostics

High co emissions

Make: Lancia
Model: Ypsilon Factory Service Manual
Year: 2003–2011
Section: Emissions › High co emissions

‹ Prev Front door water penetration Next › CO EMISSIONS LOW, NOx EMISSIONS HIGH

Fault diagnosisHigh co emissions

HIGH CO EMISSIONS

1.2 8v

The percentage of CO and/or HC is higher than the recommended figure.

0	PRELIMINARY CHECKS	All OK	Problems met	Operation
		Results of the tests
	Check the condition of the air filter	Continue to Step 1	Filter element dirty or damaged	Replace the filter element
1	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Connect the diagnostic equipment (Examiner or other instruments) to the diagnostic socket Check that there are no fault in the engine management control unit	Continue to Step 2	'Supply system' error detected	See table Z50
			'Misfire' error detected	See table Z53
			'Catalytic converter' error detected	See table Z55
			'Upstream lambda sensor' error detected	See table Z56
			'Downstream lambda sensor' error detected	See table Z58
			Another error dected in the control unit	Continue following the instructions for the diagnostic equipment.
			Lack of dialogue with the control unit	Restore the connection between the engine management control unit and the diagnostic connector See E5030 PETROL ENGINE ELECTRONIC MANAGEMENT
2	ACTIVE DIAGNOSIS WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Using the diagnostic equipment (Examiner or other iinstruments) carry out active diagnosis on the: vapour recovery soleniod valve injectors.	Continue to Step 3	Connections faulty	Restore the connection of the injectors and the solenoid with the control unit See E5030 PETROL ENGINE ELECTRONIC MANAGEMENT
			Solenoid valve faulty	Replace the solenoid valve Op. 1080E28
			Injector faulty	Replace injector Op. 1056B70
3	UPSTREAM LAMBDA SENSOR CHECK	All OK	Problems met	Operation
	Check that the upstream Lambda sensor is working properly.	Continue to Step 4	Lambda sensor faulty	Replace the Lambda sensor Op. 1080B94
4	DOWNSTREAM LAMDBA SENSOR CHECK	All OK	Problems met	Operation
	Check that the downstream Lambda sensor is working properly.	Continue to Step 5	Lambda sensor faulty	Replace the Lambda sensor Op. 1080B95
5	CHECKING AIR CIRCUIT	All OK	Problems met	Operation
	Check the condition of the air supply circuit	Continue to Step 6	Circuit component damaged	Replace the component involved
6	CHECK ON FUEL PRESSURE	All OK	Problems met	Operation
	Check the fuel supply pressure Op. 0510C10	Continue to Step 7	Pressure not correct	Replace the fuel pupm
7	CHECK ON CORRECT OPERATION	All OK	Problems met	Operation
	Check that the fault is no longer present	End of diagnosis	Fault persists

1.2 16v, 1.4 16v

The percentage of CO and/or HC is higher than the recommended figure.

0	PRELIMINARY CHECKS	All OK	Problems met	Operation
		Results of the tests
	Check the condition of the air filter	Continue to Step 1	Filter element dirty or damaged	Replace the filter element
1	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Connect the diagnostic equipment (Examiner or other instruments) to the diagnostic socket Check that there are no fault in the engine management control unit	Continue to Step 2	'Supply system' error detected	See table Z50
			'Misfire' error detected	See table Z53
			'Catalytic converter' error detected	See table Z55
			'Upstream Lambda signal' error detected	See table Z56
			'Downstream Lambda signal' error detected	See table Z58
			Another error dected in the control unit	Continue following the instructions for the diagnostic equipment.
			Lack of dialogue with the control unit	Restore the connection between the engine management control unit and the diagnostic connector
2	ACTIVE DIAGNOSIS WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Using the diagnostic equipment (Examiner or other iinstruments) carry out active diagnosis on the: vapour recovery soleniod valve injectors.	Continue to Step 3	Connections faulty	Restore the connection of the injectors and the solenoid with the control unit
			Solenoid valve faulty	Replace the solenoid valve Op. 1080E28
			Injector faulty	Replace injector Op. 1056B70
3	UPSTREAM LAMBDA SENSOR CHECK	All OK	Problems met	Operation
	Check that the upstream Lambda sensor is working properly.	Continue to Step 4	Lambda sensor faulty	Replace the Lambda sensor Op. 1080B94
4	DOWNSTREAM LAMDBA SENSOR CHECK	All OK	Problems met	Operation
	Check that the downstream Lambda sensor is working properly.	Continue to Step 5	Lambda sensor faulty	Replace the Lambda sensor Op. 1080B95
5	CHECKING AIR CIRCUIT	All OK	Problems met	Operation
	Check the condition of the air supply circuit	Continue to Step 6	Circuit component damaged	Replace the component involved
6	CHECK ON FUEL PRESSURE	All OK	Problems met	Operation
	Check the fuel supply pressure Op. 0510C10	Continue to Step 7	Pressure not correct	Replace the fuel pupm
7	CHECK ON CORRECT OPERATION	All OK	Problems met	Operation
	Check that the fault is no longer present	End of diagnosis	Fault persists

‹ Prev Front door water penetration Next › CO EMISSIONS LOW, NOx EMISSIONS HIGH

Parts & tools for this job Staging For 2003 Lancia Ypsilon

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.