Timing system protective cover(s) - r + r
- Make
- Lancia
- Model
- Ypsilon Factory Service Manual
- Year
- 2003–2011
- Section
- Timing system › Timing system protective cover(s) - r + r
Timing system protective cover(s) - r + r
Removing
Ensure that the ignition key is in OFF position, then disconnect the battery negative terminal (-).
| Name | Connector | |
|---|---|---|
| Battery | A1B |
1. Disconnect the electrical connection for the rpm sensor.
| Name | Connector | |
|---|---|---|
| 1 | Rpm sensor | K46 |
2. Release the electrical wiring for the rpm sensor from the band.
Removing
Position the vehicle on the ramp.
Proceed with removal - 4450B04 right front wheel r r.
Proceed with removal - 7055B66 Engine compartment DUST SHIELD protection in right front wheel arch - R.R..
Proceed with removal - 1008B10 power unit front mount (timing side) flexible block - replace.
1. Undo the bolts fixing the power unit timing side rigid mount.
2. Undo the bolts (2a) and remove the upper protective timing cover (2b).
Removing
Position the vehicle on the ramp.
Proceed with removal - 4450B04 right front wheel r r.
Proceed with removal - 7055B66 Engine compartment DUST SHIELD protection in right front wheel arch - R.R..
Proceed with removal - 1008B10 power unit front mount (timing side) flexible block - replace.
1. Undo the bolts fixing the power unit timing side rigid mount.
2. Undo the bolts (2a) and remove the upper protective timing cover (2b).
Disconnect the electrical connection from the cam angle sensor.
| Name | Connector | |
|---|---|---|
| Timing sensor | K47 |
Proceed with removal - 1008B10 power unit front mount (timing side) flexible block - replace.
Proceed with removal - 1008A46 cam shaft left rigid mount - r r.
1. Undo the bolts (1a) and remove the upper protective timing cover (1b).
1. Undo the bolts (1a) and remove the lower protective timing cover (1b).
1. Undo the bolts (1a) and remove the lower protective timing cover (1b).
1. Undo the bolts (1a) and remove the lower protective timing cover (1b).
Refitting
Fit the lower protective timing cover and secure using the bolts.
Fit the upper protective timing gear cover and fix it using the bolts.
Tighten the bolts fixing the power unit rigid support to the recommended torque.
| Fastening | Component | Ø | Value (daNm) |
|---|
Proceed with refitting - 1008B10 power unit front mount (timing side) flexible block - replace.
Proceed with refitting - 7055B66 Engine compartment DUST SHIELD protection in right front wheel arch - R.R..
Proceed with refitting - 4450B04 right front wheel r r.
Remove the car from the ramps.
Refitting
Fit the lower protective timing cover and secure using the bolts.
Fit the upper protective timing gear cover and fix it using the bolts.
Tighten the bolts fixing the power unit rigid timing side mount to the recommended torque.
| Fastening | Component | Ø | Value (daNm) |
|---|
Proceed with refitting - 1008B10 power unit front mount (timing side) flexible block - replace.
Proceed with refitting - 7055B66 Engine compartment DUST SHIELD protection in right front wheel arch - R.R..
Proceed with refitting - 4450B04 right front wheel r r.
Remove the car from the ramps.
Refitting
Fit the lower protective timing cover and secure using the bolts.
Fit the upper protective timing gear cover and fix it using the bolt.
Proceed with refitting - 1008A46 cam shaft left rigid mount - r r.
Proceed with refitting - 1008B10 power unit front mount (timing side) flexible block - replace.
Connect the electrical connection to the cam angle sensor.
Fix the electrical wiring for the rpm sensor using the band.
Connect the electrical connection for the rpm sensor.
Connect the negative (-) battery terminal.
Parts & tools for this job Staging For 2003 Lancia Ypsilon
- PARTEngine gasket setSearch: Lancia Ypsilon 2003 engine gasket set
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLFeeler gauge setSearch: feeler gauge set
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.