Workshop Manuals Factory service & repair Lancia
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Axles and driveshafts12 Brakes13 Steering14 Suspension and wheels15 Heating, air conditioning and auxiliary units16 Electrical equipment17 Body fittings18 Body panels and frame19 Wiring diagrams and electrical functions20 Wiring harnesses21 Connectors and pin-outs22 Fault diagnosis23 Special tools
Lancia Ypsilon Factory Service Manual (2003-2011)08 · Engine
08 · Engine

Emgine oil intake duct - r r

Make
Lancia
Model
Ypsilon Factory Service Manual
Year
2003–2011
Section
Engine lubrication system › Emgine oil intake duct - r r
EngineEmgine oil intake duct - r r

Emgine oil intake duct - r r

Operation 1084B26 · Engine oil lubrication circuit

1.3 JTD

Removing

Position the vehicle on the ramp.

Make sure that the ignition key is in the OFF position; then disconnect the battery negative (-) terminal.

NameConnector
BatteryA1B

Drain the air conditioner coolant circuit - 0010T84 coolant for air conditioning system dehydrate and recharge.

Proceed with removal - 4450B04 right front wheel r r.

Proceed with removal - 7055B66 Engine compartment DUST SHIELD protection in right front wheel arch - R.R..

Proceed with removal - 7055B91 Right front WHEEL ARCH LINER - R.R..

Proceed with removal - 1092G10 single engine belt r r.

Proceed with removal - 1092A10 Crankshaft services PULLEY - R.R..

Proceed with removal.

Proceed with removal - 2110A60 manual gearbox/engine coupling bracket - r+r.

Proceed with removal - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Proceed with removal - 1020B10 cover of timing system with chain drive - r + r replace oil seal and gasket.

1. At the bench, undo the bolts (1a) and separate the engine oil inlet duct (1b) complete with gasket (1c) from the timing cover.

Emgine oil intake duct - r r

Refitting

Place the engine oil inlet duct, complete with gasket, back in its housing on the timing cover and secure it using the bolts.

Proceed with refitting - 1020B10 cover of timing system with chain drive - r + r replace oil seal and gasket.

Proceed with refitting - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Proceed with refitting - 2110A60 manual gearbox/engine coupling bracket - r+r.

Proceed with refitting - 1092A10 Crankshaft services PULLEY - R.R..

Proceed with refitting - 1092G10 single engine belt r r.

Proceed with refitting - 7055B91 Right front WHEEL ARCH LINER - R.R..

Proceed with refitting - 7055B66 Engine compartment DUST SHIELD protection in right front wheel arch - R.R..

Proceed with refitting - 4450B04 right front wheel r r.

Connect the negative (-) battery terminal.

Refill the engine oil lubrication system - 0010T11 engine oil check level and top up.

Refill the engine cooling system with coolant - 0010T20 coolant change.

Fill the air conditioner coolant circuit - 0010T84 coolant for air conditioning system dehydrate and recharge.

Proceed with refitting.

Remove the car from the ramps.

Parts & tools for this job Staging For 2003 Lancia Ypsilon

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.