Workshop Manuals Factory service & repair Fiat
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Axles and driveshafts12 Brakes13 Steering14 Suspension and wheels15 Heating, air conditioning and auxiliary units16 Electrical equipment17 Body fittings18 Body panels and frame19 Wiring diagrams and electrical functions20 Wiring harnesses21 Connectors and pin-outs22 Fault diagnosis23 Special tools
Fiat Doblò Factory Service Manual (2000-2010)08 · Engine
08 · Engine

Engine coolant temperature sensor - r r

Make
Fiat
Model
Doblò Factory Service Manual
Year
2000–2010
Section
Diesel fuel injection › Engine coolant temperature sensor - r r
EngineEngine coolant temperature sensor - r r

Engine coolant temperature sensor - r r

Operation 1060G14 · Pressure pump electric control

Removing

Position the car on the ramp.

Ensure that the ignition key is in the OFF position, then disconnect the negative battery terminal.

NameConnector
BatteryA1

Carry out - 7055B54 under-engine guard - r r.

Carry out - 1088D10 lower sleeve for coolant outlet from radiator - r + r.

Carry out - 5530B10 battery - r+r.

Carry out - 5530B52 Battery DRIP TRAY/SUPPORT - R.R..

1. Undo the bolts fixing the rigid engine oil vapour recirculation pipe.

2. Loosen the band and disconnect the engine oil vapour recirculation pipe from the rigid pipe.

Engine coolant temperature sensor - r r

Removing

Proceed with the removal - 5530B10 battery - r+r.

Proceed with the removal - 5530B52 Battery DRIP TRAY/SUPPORT - R.R..

1. Disconnect the electrical connection from the engine coolant temperature sensor.

NameConnector
1Data not available yet

2. Undo and remove the engine coolant temperature sensor.

Engine coolant temperature sensor - r r

1. Disconnect the electrical connection from the engine coolant temperature sensor.

NameConnector
1Data not available yet

2. Undo and remove the engine coolant temperature sensor.

Engine coolant temperature sensor - r r

Refitting

Place the engine coolant temperature sensor back in its housing and tighten it to the recommended torque.

FasteningComponentØ

Value

(daNm)

ENGINE COOLANT TEMPERATURE SENSOR.M12(Thermostat side) 1.8 ÷ 2.2

Connect the electrical connection to the engine coolant temperature sensor.

Proceed with the refitting - 5530B52 Battery DRIP TRAY/SUPPORT - R.R..

Proceed with the refitting - 5530B10 battery - r+r.

Refitting

Place the engine coolant temperature sensor back in its housing and tighten it to the recommended torque.

Restore the sealant on the sensor thread.

FasteningComponentØ

Value

(daNm)

ENGINE COOLANT TEMPERATURE SENSOR.M16(Thermostat side) 3.1 ÷ 3.7

Connect the electrical connection to the engine coolant temperature sensor.

NameConnector
Data not available yet

Connect the engine oil vapour recirculation hose to the rigid pipe and tighten the band.

Tighten the bolts securing the engine oil vapour recirculation rigid pipe.

Carry out - 5530B52 Battery DRIP TRAY/SUPPORT - R.R..

Carry out - 5530B10 battery - r+r.

Connect the lower coolant outlet hose from the radiator, radiator side, and tighten the band.

Refill the engine cooling system with coolant - 0010T20 coolant change.

Carry out - 1088D10 lower sleeve for coolant outlet from radiator - r + r.

Carry out - 7055B54 under-engine guard - r r.

Connect the battery negative terminal.

NameConnector
BatteryA1

Remove the car from the ramps.

Parts & tools for this job Staging For 2000 Fiat Doblò

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.