Gear box left rigid mount - r r
- Make
- Alfa Romeo
- Model
- GT Factory Service Manual
- Year
- 2003–2010
- Section
- Power unit supports › Gear box left rigid mount - r r
GEAR BOX LEFT RIGID MOUNT - R R
Removing
Position the vehicle on a lift.
Proceed with the removal
Op. 4450B02 LEFT FRONT WHEEL R R.
Proceed with the removal
Op. 7055B65 ENGINGE BAY DUSTGUARD PROTECTION IN LEFT FRONT WHEEL ARCH R R.
Proceed with the removal
Op. 7055B90 LEFT FRONT WHEEL ARCH LINER - R.R..
Proceed with the removal
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Position a hydraulic jack beneath the engine.
1. Undo the nut (1a) and disconnect the earth lead (1b).
| Description | Connector | |
|---|---|---|
| 1b | Battery earth | See C1 BATTERY EARTH |
2. Undo the bolts (2a), (2b) and remove the power unit gearbox side rigid support (2c).
Refitting
1. Place the power unit gearbox side rigid support (1a) in its housing and secure it tightening the bolts (1b) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1b | Bolt | POWER UNIT GEAR BOX END RIGID MOUNT | M10 | (Gearbox side) 4.5 - 5.5 |
2. Tighten the bolt securing the power unit gearbox side rigid support to the flexible mounting to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 2 |
3. Connect the earth lead and fasten it using the nut.
Remove the hydraulic jack from beneath the engine.
Proceed with the refitting
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Proceed with the refitting
Op. 7055B90 LEFT FRONT WHEEL ARCH LINER - R.R..
Proceed with the refitting
Op. 7055B65 ENGINGE BAY DUSTGUARD PROTECTION IN LEFT FRONT WHEEL ARCH R R.
Proceed with the refitting
Op. 4450B02 LEFT FRONT WHEEL R R.
Remove the vehicle from the lift.
Removing
Position the vehicle on a lift.
Proceed with the removal
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Position a hydraulic jack beneath the gearbox.
1. Undo the nut (1a) and disconnect the earth lead (1b) from the power unit gearbox side rigid support.
| Description | Connector | |
|---|---|---|
| 1b | Battery earth | See C1 BATTERY EARTH |
2. Unscrew the bolt securing the power unit rigid mount to the flexible block.
3. Undo the bolts (3a) and remove the power unit gearbox side rigid support (3b).
One of the above bolts also secures the power unit mounting bracket.
Refitting
1. Place the power unit gearbox side rigid support (1a) in its housing and secure it to the gearbox tightening the bolts (1b) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1b | Bolt | POWER UNIT GEAR BOX END RIGID MOUNT | M10 | (Manual gearbox/differential side) 4.5 - 5.5 |
2. Tighten the bolt securing the power unit gearbox side rigid support to the flexible mounting to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 2 |
3. Connect the earth lead (3a) to the power unit gearbox side rigid support and tighten the nut (3b).
Remove the hydraulic jack from beneath the gearbox
Proceed with the refitting
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Remove the vehicle from the lift.
Removing
Position the vehicle on a lift.
Proceed with the removal
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Proceed with the removal
Op. 1048B14 AIR DELIVERY PIPE BETWEEN TURBO CHARGER AND HEAT EXCHANGER - REPLACE.
Position a hydraulic jack beneath the gearbox.
1. Undo the nut (1a) and disconnect the earth lead (1b) from the power unit gearbox side rigid support.
| Description | Connector | |
|---|---|---|
| 1b | Battery earth | See C1 BATTERY EARTH |
2. Unscrew the bolt securing the power unit rigid mount to the flexible block.
3. Undo the bolts (3a) and remove the power unit gearbox side rigid support (3b).
Refitting
1. Place the power unit gearbox side rigid support (1a) in its housing and secure it to the gearbox tightening the bolts (1b) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1b | Bolt | POWER UNIT GEAR BOX END RIGID MOUNT | M10 | (Manual gearbox/differential side) 4.5 - 5.5 |
2. Tighten the bolt securing the power unit gearbox side rigid support to the flexible mounting to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 2 |
3. Connect the earth lead (3a) to the power unit gearbox side rigid support and tighten the nut (3b).
Remove the hydraulic jack from beneath the gearbox
Proceed with the refitting
Op. 1048B14 AIR DELIVERY PIPE BETWEEN TURBO CHARGER AND HEAT EXCHANGER - REPLACE.
Proceed with the refitting
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Remove the vehicle from the lift.
Removing
Position the vehicle on a lift.
Proceed with the removal
Op. 4450B02 LEFT FRONT WHEEL R R
Op. 7055B65 ENGINGE BAY DUSTGUARD PROTECTION IN LEFT FRONT WHEEL ARCH R R
Proceed with the removal
Op. 7055B90 LEFT FRONT WHEEL ARCH LINER - R.R.
Position a hydraulic jack beneath the gearbox.
1. Unscrew the bolt securing the power unit rigid mount to the flexible block.
2. Undo the bolts (2a), (2b) and remove the power unit gearbox side rigid support (2c).
Refitting
1. Place the power unit gearbox side rigid support (1a) in its housing and secure it tightening the bolts (1b) and (1c) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1b | Bolt | POWER UNIT GEAR BOX END RIGID MOUNT | M10 | (Manual gearbox/differential side) 4.5 - 5.5 |
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1c | Bolt | POWER UNIT GEAR BOX END RIGID MOUNT | M10 | (Manual gearbox/differential side) 4.5 - 5.5 |
2. Tighten the bolt securing the power unit gearbox side rigid support to the flexible mounting to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 2 | Bolt | POWER UNIT GEAR BOX END RIGID MOUNT | M10 | (Flexible mounting side) 4.2 - 5.1 |
Remove the hydraulic jack from beneath the gearbox
Op. 7055B90 LEFT FRONT WHEEL ARCH LINER - R.R.
Proceed with the refitting
Op. 7055B65 ENGINGE BAY DUSTGUARD PROTECTION IN LEFT FRONT WHEEL ARCH R R
Proceed with the refitting
Op. 4450B02 LEFT FRONT WHEEL R R
Remove the vehicle from the lift.
Parts & tools for this job Staging For 2003 Alfa Romeo GT
- PARTEngine gasket setSearch: Alfa Romeo GT 2003 engine gasket set
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLFeeler gauge setSearch: feeler gauge set
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.