Cam shaft left rigid mount - r r
- Make
- Alfa Romeo
- Model
- GT Factory Service Manual
- Year
- 2003–2010
- Section
- Power unit supports › Cam shaft left rigid mount - r r
CAM SHAFT LEFT RIGID MOUNT - R R
Removing
Position the vehicle on a lift.
Proceed with the removal
Op. 4450B04 RIGHT FRONT WHEEL R R.
Proceed with the removal
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Proceed with the removal
Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R..
Position a hydraulic jack beneath the engine.
1. Undo the bolts (1a) and (1b) and remove the timing side rigid engine support (1c).
Refitting
1. Place the timing side rigid engine support (1a) in its housing and secure it tightening the bolts (1b) and (1c) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1b |
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1c | Bolt | RIGID ENGINE MOUNT, TIMING SIDE | M12 | (Flexible mounting side) 7.9 - 9.7 |
Remove the hydraulic jack from beneath the engine.
Proceed with the refitting
Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R..
Proceed with the refitting
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Proceed with the refitting
Op. 4450B04 RIGHT FRONT WHEEL R R.
Remove the vehicle from the lift.
Removing
Position the vehicle on a lift.
Make sure that the ignition key is in the OFF position, then disconnect the negative battery terminal.
| Description | Connector | |
|---|---|---|
| Battery | See A1B BATTERY ( BATTERY NEGATIVE ) |
Drain the air conditioning refrigerant circuit
Op. 5040A10 EXPANSION/CONNECTION PIPE - R R.
Proceed with the removal
Op. 4450B04 RIGHT FRONT WHEEL R R.
Proceed with the removal
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Proceed with the removal
Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R..
Proceed with the removal
Op. 1092G10 SINGLE ENGINE BELT R R.
Proceed with the removal
Op. 5040A20 AIR CONDITIONER COMPRESSOR - R+R - INCLUDES FLUID LEVEL CHECK AND TOP UP IF NECESSARY.
Proceed with the removal
Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R..
1. Undo the bolt (1a) and remove the lower bracket (1b) fastening the power assisted steering pipes.
2. Release the engine oil pipes (2a) from the fastenings (2b).
1. Undo the bolts (1a) fixing the mounting bracket (1b) for the power assisted steering system/engine oil pipes to the timing side rigid engine support.
Position a hydraulic jack beneath the engine.
1. Loosen the nut fixing the timing side rigid engine support to the flexible mounting.
1. Undo the nuts (1a) and remove the timing side rigid engine support (1b).
Refitting
1. Place the timing side rigid engine support (1a) in its housing and secure it tightening the nuts (1b) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1b | Nut | RIGID ENGINE MOUNT, TIMING SIDE | M8 | (Engine crankcase side) 2.3 - 2.8 |
1. Tighten the nut securing the timing side rigid engine support to the flexible mounting to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1 | Nut | RIGID ENGINE MOUNT, TIMING SIDE | M10 | (Flexible mounting side) 4.5 - 5.5 |
Remove the hydraulic jack from beneath the engine.
Tighten the bolts fixing the mounting bracket for the power assisted steering system/engine oil pipes to the timing side rigid engine support.
Fasten the engine oil pipes using the bands.
Place the power assisted steering pipes lower mounting bracket in its housing and secure it using the bolt.
Proceed with the refitting
Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R..
Proceed with the refitting
Op. 5040A20 AIR CONDITIONER COMPRESSOR - R+R - INCLUDES FLUID LEVEL CHECK AND TOP UP IF NECESSARY.
Proceed with the refitting
Op. 1092G10 SINGLE ENGINE BELT R R.
Proceed with the refitting
Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R..
Proceed with the refitting
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Proceed with the refitting
Op. 4450B04 RIGHT FRONT WHEEL R R.
Refill the air conditioning refrigerant circuit
Op. 5040A10 EXPANSION/CONNECTION PIPE - R R.
Connect the negative battery terminal (-).
Remove the vehicle from the lift.
Removing
Position the vehicle on a lift.
Proceed with the removal
Op. 4450B04 RIGHT FRONT WHEEL R R.
Proceed with the removal
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Proceed with the removal
Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R..
Proceed with the removal
Op. 1092G10 SINGLE ENGINE BELT R R.
Proceed with the removal
Op. 1092A10 CRANKSHAFT SERVICES PULLEY - R.R..
Position a hydraulic jack beneath the engine.
1. Loosen the bolt fixing the timing side rigid engine support to the flexible mounting.
2. Undo the bolts (2a) and remove the timing side rigid engine support (2b).
Refitting
1. Place the timing side rigid engine support (1a) in its housing and secure it tightening the bolts (1b) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1b | Bolt | RIGID ENGINE MOUNT, TIMING SIDE | M10 | (Engine crankcase side) 4.5 - 5.5 |
2. Tighten the bolt securing the timing side rigid engine support to the flexible mounting to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 2 | Bolt | RIGID ENGINE MOUNT, TIMING SIDE | M12 | (Flexible mounting side) 7.9 - 9.7 |
Remove the hydraulic jack from beneath the engine.
Proceed with the refitting
Op. 1092A10 CRANKSHAFT SERVICES PULLEY - R.R..
Proceed with the refitting
Op. 1092G10 SINGLE ENGINE BELT R R.
Proceed with the refitting
Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R..
Proceed with the refitting
Op. 7055B54 UNDER-ENGINE GUARD - R R.
Proceed with the refitting
Op. 4450B04 RIGHT FRONT WHEEL R R.
Remove the vehicle from the lift.
Removing
Position the vehicle on a lift.
Proceed with the removal
Op. 4450B04 RUOTA ANTERIORE DESTRA - S.R.
Proceed with the removal
Op. 7055B66 PROTEZIONE PARAPOLVERE VANO MOTORE NEL PASSARUOTA ANTERIORE DESTRO - S.R.
Position a hydraulic jack beneath the engine.
1. Undo the bolts (1a) and (1b), then remove the timing side rigid engine support (1c).
Refitting
1. Place the timing side rigid engine support (1a) in its housing and secure it to the crankcase tightening the bolts (1b) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1b | Bolt | RIGID ENGINE MOUNT, TIMING SIDE | M10 | (Engine crankcase side) 4.5 - 5.5 |
2. Tighten the bolt securing the timing side rigid engine support to the flexible mounting to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 2 | Bolt | RIGID ENGINE MOUNT, TIMING SIDE | M12 | (Flexible mounting side) 7.9 - 9.7 |
Remove the hydraulic jack from beneath the engine.
Proceed with the refitting
Op. 7055B66 PROTEZIONE PARAPOLVERE VANO MOTORE NEL PASSARUOTA ANTERIORE DESTRO - S.R.
Proceed with the refitting
Op. 4450B04 RUOTA ANTERIORE DESTRA - S.R.
Remove the vehicle from the lift.
Parts & tools for this job Staging For 2003 Alfa Romeo GT
- PARTEngine gasket setSearch: Alfa Romeo GT 2003 engine gasket set
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLFeeler gauge setSearch: feeler gauge set
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.