Rhp brake connection pipe - r r
- Make
- Alfa Romeo
- Model
- GT Factory Service Manual
- Year
- 2003–2010
- Section
- Anti-lock brake system – ABS › Rhp brake connection pipe - r r
RHP BRAKE CONNECTION PIPE - R R
Removing
Position the vehicle on the ramp
Remove the handbrake boot.
1. Lift up the handbrake lever (1a) and loosen the nut (1b) adjusting the tension of the handbrake cables.
Proceed with removal
Op. 1076B20 REAR EXHAUST SILENCER - R + R
Proceed with removal
Op. 1076B18 RIGID SECTION OF EXHAUST PIPE BETWEEN CATALYTIC CONVERTER AND SILENCER - R + R
1. Release the handbrake cable from the mounting bracket.
2. Remove the retaining clips (2a), undo the bolt (2b) and remove the intermediate heat shield (2c).
1. Release the rigid pipe from the connector to the left rear brake from the attachments on the underbody.
2. Undo the connector (2a) and disconnect the rigid pipe from the connector to the left rear brake (2b), connector side.
1. Undo the connector (1a) and disconnect the rigid pipe from the connector to the left rear brake (1b), left rear brake side.
2. Remove the rigid pipe from connector to rear left brake.
Refitting
1. Refit in its seating the rigid pipe from connector to rear left brake.
2. Connect the rigid pipe from the connector to the left rear brake (2a), left rear brake side, and tighten the connector (2b) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 2b | Connector | RIGID PIPE FROM FITTING | M10 | (Rear brake caliper flexible pipe side.) 1.4 ÷ 1.8 |
1. Connect the rigid pipe from the connector to the left rear brake (1a), connector side, and tighten the connector (1b) to the recommended torque.
| Fastening | Component | Ø | Value (daNm) | |
|---|---|---|---|---|
| 1b | Connector | RIGID PIPE FROM FITTING | M10 | (Connector side) 1.4 ÷ 1.8 |
2. Secure the rigid pipe from the connector to the left rear brake to the attachments on the underbody.
Refit in its seating the intermediate heat shield, and secure it with the bolt and clips.
Secure the handbrake cable to the mounting bracket.
Proceed with refitting
Op. 1076B18 RIGID SECTION OF EXHAUST PIPE BETWEEN CATALYTIC CONVERTER AND SILENCER - R + R.
Proceed with refitting
Op. 1076B20 REAR EXHAUST SILENCER - R + R.
Proceed with refitting
Op. 0010T64 BRAKE AND OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY.
Proceed with refitting
Op. 0010T65 HYDRAULIC BRAKE SYSTEM BLEED AIR.
Adjust the travel of the handbrake lever
Op. 3380A04 HANDBRAKE - CHECK TRAVEL.
Place the handbrake boot back in its housing.
Remove the car from the ramps.
Proceed with removal
Op. 1076B22 REAR EXHAUST SILENCER - R+R EMISSION CONTROL VERSIONS
Proceed with removal
Op. 1076B26 INTERMEDIATE EXHAUST SILENCER - R+R EMISSION CONTROL VERSIONS
Proceed with removal
Op. 1076B20 REAR EXHAUST SILENCER - R + R
Proceed with removal
Op. 1076B24 INTERMEDIATE EXHAUST SILENCER - R + R
Proceed with refitting
Op. 1076B24 INTERMEDIATE EXHAUST SILENCER - R + R.
Proceed with refitting
Op. 1076B20 REAR EXHAUST SILENCER - R + R.
Proceed with refitting
Op. 1076B26 INTERMEDIATE EXHAUST SILENCER - R+R EMISSION CONTROL VERSIONS.
Proceed with refitting
Op. 1076B22 REAR EXHAUST SILENCER - R+R EMISSION CONTROL VERSIONS.
Parts & tools for this job Staging For 2003 Alfa Romeo GT
- PARTBrake padsSearch: Alfa Romeo GT 2003 brake pads
- TOOLBrake bleeder kitSearch: one man brake bleeder kit
- FLUIDBrake fluidSearch: brake fluid
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.