Gear hand-lever - r r

Operation 2125C16 · Manual gearbox external control (cables)

1.2 8v, 1.2 16v, 1.4 16v

Removing

Position the vehicle on the ramp.

Proceed with removal - 5530B10 battery - r+r.

Proceed with removal - 5530B52 Battery DRIP TRAY/SUPPORT - R.R..

1. Press the release button (1a) and disconnect the gear selector cable (1b).

2. Disconnect the gear engagement cable.

3. Remove the clips (3a) and release the gear selector and engagement cables (3b) from the mounting bracket.

1.3 JTD

Removing

Position the vehicle on the ramp.

Proceed with removal - 5530B10 battery - r+r.

Proceed with removal - 5530B52 Battery DRIP TRAY/SUPPORT - R.R..

1. Disconnect the gear engagement/selector cables.

2. Remove the stops and release the gear engagement/selector cables from the mounting bracket.

1.2 8v, 1.2 16v, 1.4 16v

1. Release the gear selector and engagement cables from the fastening on the steering box, then remove them from the engine compartment.

1.3 JTD

1. Release the gear selector and engagement cables from the fastening on the steering box, then remove them from the engine compartment.

1.2 8v, 1.2 16v, 1.4 16v

1. Undo the nuts fixing the exhaust manifold and catalytic converter to the exhaust silencer.

2. Undo the bolt fixing the exhaust silencer front mounting bracket.

1.3 JTD

1. Tighten the nuts fastening the rigid section of the exhaust pipe between the catalytic converter and the silencer, silencer side.

2. Undo the bolt fixing the exhaust silencer front mounting bracket.

1.2 8v, 1.2 16v, 1.4 16v

1. Undo the bolts (1a) and remove the exhaust pipe heat shield (1b).

1.3 JTD

1. Undo the bolts (1a) and remove the gear lever mounting (1b) after having released it from the gear selector and engagement cable rubber mountings.

1.2 8v, 1.2 16v, 1.4 16v

1. Undo the bolts (1a) and remove the gear lever mounting (1b) after having released it from the gear selector and engagement cable rubber mountings.

1.3 JTD

Refitting

Place the gear lever mounting in its housing and secure it using the bolts.

Check that the gear selector and engagement cable rubber mountings are correctly positioned.

Tighten the bolt fixing the exhaust silencer front mounting bracket.

Tighten the nuts fastening the rigid section of the exhaust pipe between the catalytic converter and the silencer, silencer side.

Fit the gear selector and engagement cables in the engine compartment and fasten the band to the steering box.

Secure the gear engagement/selector cables to the mounting bracket with the stops.

Connect the gear engagement/selector cables.

Proceed with refitting - 5530B52 Battery DRIP TRAY/SUPPORT - R.R..

Proceed with refitting - 5530B10 battery - r+r.

Remove the car from the ramps.

1.2 8v, 1.2 16v, 1.4 16v

Refitting

Place the gear lever mounting in its housing and secure it using the bolts.

Check that the gear selector and engagement cable rubber mountings are correctly positioned.

Place the exhaust pipe heat shield back in its housing and secure it using the bolts.

Tighten the bolt fixing the exhaust silencer front mounting bracket.

Tighten the nuts fixing the exhaust manifold and catalytic converter to the exhaust silencer to the recommended torque.

Fit the gear selector and engagement cables in the engine compartment and fasten the band to the steering box.

Position the gear selector and engagement cables in the housings in the mounting bracket and secure them using the clips.

Connect the gear selector and engagement cables.

Proceed with refitting - 5530B52 Battery DRIP TRAY/SUPPORT - R.R..

Proceed with refitting - 5530B10 battery - r+r.

Remove the car from the ramps.