60,000KM SERVICE

Operation 0010K60 · PROGRAMMED MAINTENANCE, EMISSION CONTROL VERSIONS UP TO 90,000KM

2.2 JTS

- Check the tyre tread is not worn.

Some types of tyre are fitted with wear indicators; they should be replaced as soon as these indicators are visible on the tread.

Do not swap tyres across.

- Check the tyre inflation pressure is correct. Also check the spare wheel.

The tyre pressures must be checked when they are cold.

- Check that the lighting system is operating correctly: headlamps, turn signals, hazard lights, luggage compartment light, passenger compartment light, oddment compartment light and instrument panel warning lights.

- Check the windscreen wiper system is operating correctly and adjust the sprays if necessary.

- Check the front and rear wiper blades are correctly positioned and not worn.

- Check condition and wear of front disc brake pads and operation of pad wear indicator.

- Check rear disc brake pad condition and wear

- Carry out a visual check of: exterior bodywork, underbody protection, rigid and flexible pipes (exhaust - fuel system - braking system) rubber elements (boots - hoses - bushes - etc.)

- Check cleanliness of locks, bonnet and boot lids, cleanliness and lubrication of linkage

- Check and, if necessary, top up the engine fluid levels: brakes/clutch,

Op. 0010T64 BRAKE AND/OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY

power steering,

Op. 0010T71 POWER STEERING FLUID CHECK LEVEL AND TOP UP IF NECESSARY

windscreen washer, battery, engine cooling, etc.

- Visually inspect condition of auxiliary drive belt/s

- Check exhaust emissions

Op. 1080A10 IDLING C.O. LEVEL - CHECK WITH SPECIAL EQUIPMENT

- Replace the air filter cartridge

Op. 1048A14 AIR CLEANER FILTER ELEMENT - REPLACE.

- Replace engine oil and filter

Op. 0010T12 ENGINE OIL AND FILTER - REPLACE

- Replace the brake fluid

Op. 0010T64 BRAKE AND/OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY

- Replace the pollen filter.

Op. 5010B09 PURIFYING (POLLEN) FILTER FILTER ELEMENT - REPLACE

- Connect the Examiner diagnostic equipment to the vehicle diagnostic socket and check the engine operation.

At the end of the service, connect the Examiner diagnostic equipment to the on board diagnostic socket to zero the mileage counter for the days to the starting value and write the details of the service that has been carried out (date, service no., total mileage) in the Trip Computer memory which can only be read using the diagnostic equipment.

Check that the figure has been set in the instrument panel in km or miles depending on the unit of measurement in that country.

3.2 JTS

- Check the tyre tread is not worn.

Some types of tyre are fitted with wear gauges; they should be replaced as soon as these gauges are visible on the tread.

Do not swap tyres across.

- Check the tyre inflation pressure is correct. Also check the spare wheel.

The tyre pressures must be checked when they are cold.

- Check that the lighting system is operating correctly: headlamps, turn signals, hazard lights, luggage compartment light, passenger compartment light, oddment compartment light and instrument panel warning lights.

- Check the windscreen wiper system is operating correctly and adjust the sprays if necessary.

- Check the front and rear wiper blades are correctly positioned and not worn.

- Check condition and wear of front disc brake pads and operation of pad wear indicator

- Check rear disc brake pad condition and wear

- Carry out a visual check of: exterior bodywork, underbody protection, rigid and flexible pipes (exhaust - fuel system - braking system) rubber elements (boots - hoses - bushes - etc.)

- Check cleanliness of locks, bonnet and boot lids, cleanliness and lubrication of linkage

- Check and, if necessary, top up the engine fluid levels: power assisted steering, screen washer, battery, engine cooling, etc.

Op. 0010T71 POWER STEERING FLUID CHECK LEVEL AND TOP UP IF NECESSARY

Op. 0010T21 ENGINE COOLANT - CHECK DENSITY AND CHANGE, IF NECESSARY

- Visually inspect condition of auxiliary drive belt/s.

- Check exhaust emissions.

Op. 1080A10 IDLING C.O. LEVEL - CHECK WITH SPECIAL EQUIPMENT

- Replace the air filter cartridge.

Op. 1048A14 AIR CLEANER FILTER ELEMENT - REPLACE.

- Replace engine oil and filter.

Op. 0010T12 ENGINE OIL AND FILTER - REPLACE

- Replace the brake fluid.

Op. 0010T64 BRAKE AND/OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY

Op. 0010T65 HYDRAULIC BRAKE SYSTEM - BLEED AIR

- Replace the pollen filter.

Op. 5010B09 PURIFYING (POLLEN) FILTER FILTER ELEMENT - REPLACE

- Connect the Examiner diagnostic equipment to the vehicle diagnostic socket and check the engine operation.

At the end of the service, connect the Examiner diagnostic equipment to the on board diagnostic socket to zero the mileage counter for the days to the starting value and write the details of the service that has been carried out (date, service no., total mileage) in the Trip Computer memory which can only be read using the diagnostic equipment.

Check that the figure has been set in the instrument panel in km or miles depending on the unit of measurement in that country.

2.4 JTD 20v

- Check the tyre tread is not worn.

Some types of tyre are fitted with wear indicators; they should be replaced as soon as these indicators are visible on the tread.

Do not swap tyres across.

- Check the tyre inflation pressure is correct. Also check the spare wheel.

The tyre pressures must be checked when they are cold.

- Check that the lighting system is operating correctly: headlamps, turn signals, hazard lights, luggage compartment light, passenger compartment light, oddment compartment light and instrument panel warning lights.

- Check the windscreen wiper system is operating correctly and adjust the sprays if necessary.

- Check the front and rear wiper blades are correctly positioned and not worn.

- Check condition and wear of front disc brake pads and operation of pad wear indicator

- Check rear disc brake pad condition and wear

- Carry out a visual check of: exterior bodywork, underbody protection, rigid and flexible pipes (exhaust - fuel system - braking system) rubber elements (boots - hoses - bushes - etc.)

- Check cleanliness of locks, bonnet and boot lids, cleanliness and lubrication of linkage

- Check and, if necessary, top up the engine fluid levels: power steering,

Op. 0010T71 POWER STEERING FLUID CHECK LEVEL AND TOP UP IF NECESSARY

windscreen washer, battery, engine cooling, etc.

- Visually inspect condition of auxiliary drive belt/s

- Check emissions/fumes

Op. 1080A20 EXHAUST FUMES - CHECK WITH OPACIMETER

- Replace the fuel filter.

Op. 1044B10 FUEL FILTER ASSEMBLY - R + R OR REPLACE

- Replace the air filter cartridge.

Op. 1048A14 AIR CLEANER FILTER ELEMENT - REPLACE.

- Replace engine oil and filter

Op. 0010T12 ENGINE OIL AND FILTER - REPLACE

The actual interval for changing the oil and replacing the engine oil filter depends on the vehicle usage conditions and is signalled by the warning light or message (if present) in the instrument panel Change engine oil and replace oil filter (or every 24 months)

- Replace the brake fluid.

Op. 0010T62 BRAKE AND/OR CLUTCH FLUID - REPLACE FLUID INCLUDES WASHING PIPES AND BLEEDING AIR

Indipendentemente dalla percorrenza chilometrica deve essere sostituito ogni 24 mesi.

- Replace the pollen filter.

Op. 5010B09 PURIFYING (POLLEN) FILTER FILTER ELEMENT - REPLACE

Indipendentemente dalla percorrenza chilometrica deve essere sostituito ogni 24 mesi.

- Connect the Examiner diagnostic equipment to the vehicle diagnostic socket and check the engine operation.

At the end of the service, connect the Examiner diagnostic equipment to the on board diagnostic socket to zero the mileage counter for the days to the starting value and write the details of the service that has been carried out (date, service no., total mileage) in the Trip Computer memory which can only be read using the diagnostic equipment.

Check that the figure has been set in the instrument panel in km or miles depending on the unit of measurement in that country.