Check engine control unit connections
- Make
- Alfa Romeo
- Model
- Brera and Spider Factory Service Manual
- Year
- 2005–2010
- Section
- Diesel injection system › Check engine control unit connections
CHECK ENGINE CONTROL UNIT CONNECTIONS
| STEP | CHECK TO BE PERFORMED | RESOLUTION IF THE CHECK IS NOT OK |
|---|---|---|
| 1 | Press the START/STOP button and turn off the engine. Connect the wiring harness connector from the accelerator pedal potentiometer Press the START/STOP button. Select the following system on the diagnostic equipment: Diesel EDC16C39 electronic injection system. Check that error P0641 – Power supply to sensors 1 is “Present”. Move on to Step 5 | Move on to Step 2 |
| 2 | Press the START/STOP button. Disconnect the wiring harness connector from engine control unit connector A Press the START/STOP button. Check that the voltage across pin 9 of the control unit See M010 ENGINE MANAGEMENT ECU and the earth is greater than 0.3 V. | Repair or if necessary replace the electrical wiring between the accelerator pedal potentiometer and the engine control unit |
| 3 | Check that the voltage across pin 30 of the control unit See M010 ENGINE MANAGEMENT ECU and the earth is greater than 0.3 V. | Repair or if necessary replace the electrical wiring between the accelerator pedal potentiometer and the engine control unit |
| 4 | Replace the accelerator pedal Op. 1068A20 ACCELERATOR PEDAL WITH BUILT-IN POTENTIOMETER - R.R and check the fault has disappeared. The test can be considered over | Repair the original accelerator pedal and replace the engine management control unit. |
| 5 | Press the START/STOP button. Disconnect the wiring harness connector from the timing sensor. Press the START/STOP button. Select the following system on the diagnostic equipment: Diesel EDC16C39 electronic injection system. Check that error P0641 – Power supply to sensors 1 is “Present”. | Replace the timing sensor Op. 5510C30 ENGINE TIMING SENSOR - R+R |
| 6 | Press the START/STOP button. Disconnect the wiring harness connector from engine control unit connector A Press the START/STOP button. Check that the voltage across pin 45 of the control unit See M010 ENGINE MANAGEMENT ECU and the earth is greater than 0.3 V. Move on to Step 8 | Move on to Step 7 |
| 7 | If faults are present, repair or if necessary replace the electrical wiring between the engine control unit and the accelerator pedal potentiometer. See E5050 DIESEL ENGINES ELECTRONIC MANAGEMENT Replace the wiring if necessary The test can be considered over | Replace the accelerator pedal Op. 1068A20 ACCELERATOR PEDAL WITH BUILT-IN POTENTIOMETER - R.R |
| 8 | Press the START/STOP button. Check that the voltage across pin 30 of the control unit See M010 ENGINE MANAGEMENT ECU and the earth is more than 500 kOhm. | Repair or if necessary replace the electrical wiring between the accelerator pedal potentiometer and the engine control unit |
| 9 | Disconnect the wiring harness connector from engine control unit connector B Press the START/STOP button. Check that the voltage across Pin 11 of the control unit See M010 ENGINE MANAGEMENT ECU and the earth is greater than 0.3 V. | Repair or if necessary replace the electrical wiring between the timing sensor and the engine control unit |
| 10 | Press the START/STOP button. Check that the voltage across pin 11 of the control unit See M010 ENGINE MANAGEMENT ECU and the earth is more than 500 kOhm. | Repair or if necessary replace the electrical wiring between the timing sensor and the engine control unit |
| 11 | Replace the engine management control unit |
Parts & tools for this job Staging For 2005 Alfa Romeo Brera
- PARTEngine gasket setSearch: Alfa Romeo Brera 2005 engine gasket set
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLFeeler gauge setSearch: feeler gauge set
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.